Switching Devices

ACOPOSMULTI SAFEMOTION ENDAT 2.2 INVERTER MODULE, 3.8 A, HV, WALL MOUNTING, 2 AXES

X20 BUS CONTROLLER BASE FOR X20BC008T AND X20 FEED-IN MODULE, X20 TERMINATION PLATES LEFT AND RIGHT X20AC0SL1/X20AC0SR1 INCLUDED

BUS BASE WITH 2 EXPANSION SLOTS THE BUS MODULE HAS 2 EXPANSION SLOTS. THE FOLLOWING MODULES ARE USED ON THIS MODULE: BASE MODULE (BC, HB, ETC.) TWO ADD-ON MODULES (IF, HB, ETC.) SUPPLY MODULE THE LEFT AND RIGHT END COVER PLATES ARE INCLUDED IN DELIVERY.

POWERLINK I/O CONFIGURATION AND FIRMWARE UPDATE VIA THE FIELDBUS INTEGRATED HUB FOR ECONOMICAL WIRING THE BUS CONTROLLER MAKES IT POSSIBLE TO CONNECT X2X LINK I/O NODES TO POWERLINK. IT IS ALSO POSSIBLE TO OPERATE THE X2X LINK CYCLE SYNCHRONOUSLY 1:1 OR SYNCHRONOUS TO POWERLINK USING A PRESCALER.

BASIS FOR ALL POWER SUPPLY MODULES FOR CREATING POTENTIAL GROUPS THE INTERNAL I/O POWER SUPPLY IS INTERRUPTED TO THE LEFT. THE BUS MODULE IS THE BASE FOR ALL POWER SUPPLY MODULES.

THE BUS MODULE IS THE BASE FOR ALL X20 SUPPLY MODULES FOR CREATING VOLTAGE GROUPS THE INTERNAL I/O SUPPLY IS ISOLATED TO THE LEFT MANUAL NODE NUMBER ASSIGNMENT INDEPENDENT OF ELECTRONICS MODULE MANUAL AND AUTOMATIC ADDRESSING CAN BE COMBINED AS DESIRED THE BM05 BUS MODULE IS THE BASE FOR ALL X20 SUPPLY MODULES. THIS BUS MODULE IS ALSO USED TO DETERMINE A UNIQUE ADDRESS USING NODE NUMBER SWITCHES.

THE BUS MODULE IS THE BASE FOR ALL X20 24 VDC I/O MODULES THE INTERNAL I/O SUPPLY IS INTERCONNECTED MANUAL NODE NUMBER ASSIGNMENT INDEPENDENT OF ELECTRONICS MODULE MANUAL AND AUTOMATIC ADDRESSING CAN BE COMBINED AS DESIRED THE BM15 BUS MODULE SERVES AS THE BASE FOR ALL 24 VDC X20 I/O MODULES. THIS BUS MODULE IS ALSO USED TO DETERMINE A UNIQUE ADDRESS USING NODE NUMBER SWITCHES.

X20 BUS MODULE, COATED, FOR X20 SAFEIO MODULES, INTERNAL I/O SUPPLY CONNECTED THROUGH

X2X LINK BUS RECEIVER FEED FOR X2X LINK AND INTERNAL I/O SUPPLY ELECTRICAL ISOLATION OF FEED AND X2X LINK SUPPLY REDUNDANCY OF X2X LINK SUPPLY POSSIBLE BY OPERATING MULTIPLE SUPPLY MODULES SIMULTANEOUSLY OPERATION ONLY ON THE SLOT TO THE FAR LEFT THE BUS RECEIVER IS USED TO CONNECT THE X20 SYSTEM TO THE X2X LINK. THE MODULE IS EQUIPPED WITH A FEED FOR THE X2X LINK AS WELL AS THE INTERNAL I/O SUPPLY.

X20 INTERFACE MODULE, 1 RS422/485 INTERFACE, MAX. 115.2 KBIT/S

HUB EXPANSION MODULE 2X HUB 100 BASE-TX POWERLINK BUS CONTROLLER X20BC8083, STANDALONE HUB X20HB8880 AND THE POWERLINK TCP/IP GATEWAY X20HB8815 ARE EQUIPPED WITH A MODULAR HUB EXTENSION. 1 OR 2 ADDITIONAL SLOTS ARE AVAILABLE DEPENDING ON THE BUS BASE. THE X20HB2880 HUB EXPANSION MODULE CAN BE OPERATED IN THESE SLOTS. THE STATUS OF THE MODULE AND NETWORK ARE INDICATED BY LEDS.

2X / 4X / 6X FAST ETHERNET HUB MODULAR CONSTRUCTION EASILY EXPANDABLE THE X20 HUB IS A DEVICE THAT CAN BE USED UNIVERSALLY IN STANDARD ETHERNET NETWORKS OR POWERLINK NETWORKS. IT IS SUITABLE FOR 100 MBIT/S (FAST ETHERNET) NETWORKS. THE BUS MODULES EXPANDED TO THE LEFT ALLOW CONNECTION OF UP TO 2 HUB EXPANSION MODULES IN ADDITION TO THE HUB BASE MODULE. THIS MEANS THAT A SINGLE BASE DEVICE PROVIDES UP TO 6 HUB INTERFACES.

X20PS3300 DESCRIPTION: FEED FOR X2X LINK AND INTERNAL I/O SUPPLY ELECTRICAL ISOLATION OF FEED AND X2X LINK SUPPLY REDUNDANCY OF X2X LINK SUPPLY POSSIBLE BY OPERATING MULTIPLE SUPPLY MODULES SIMULTANEOUSLY THE SUPPLY MODULE IS EQUIPPED WITH A FEED FOR THE X2X LINK AS WELL AS THE INTERNAL I/O SUPPLY.

2 SAFETY RELAY OUTPUTS RELAY OUTPUT TYPE RELAY MODULE FOR 230 VAC / 24 VDC SWITCHING CURRENT 6 A NORMALLY OPEN CONTACTS INDIVIDUALLY ISOLATED OUTPUTS