B&R

X20 Digital Output Module, 8 Outputs, 24 VDC, 0.5 A, Source, 1-Wire Technology

X20 Safe digital input module, 4 safe digital inputs type A, input filter configurable, 4 pulse outputs, 24 VDC

POWERLINK/Ethernet connection cable, RJ45 to RJ45, 0.25 m

X67 DIN rail mounting plate

X20 bus transmitter, X2X link, power supply for internal I/O supply

X20 Analog input module, 2 inputs, ±10 V or 0 to 20 mA / 4 to 20 mA, 13-bit converter resolution, configurable input filter

X20 interface module, 1 RS422/485 interface, max. 115.2 kbit/s

X20 bus module, coated, for X20 SafeIO modules, internal I/O supply connected through

Hub expansion module 2x hub 100 BASE-TX POWERLINK bus controller X20BC8083, standalone hub X20HB8880 and the POWERLINK TCP/IP gateway X20HB8815 are equipped with a modular hub extension. 1 or 2 additional slots are available depending on the bus base. The X20HB2880 hub expansion module can be operated in these slots. The status of the module and network are indicated by LEDs.

X20 Digital counter module, 1 SSI absolute encoder, 5 V, 1 Mbit/s, 32 bits

The bus module is the base for all X20 supply modules For creating voltage groups The internal I/O supply is isolated to the left Manual node number assignment Independent of electronics module Manual and automatic addressing can be combined as desired The BM05 bus module is the base for all X20 supply modules. This bus module is also used to determine a unique address using node number switches.

Basis for all power supply modules For creating potential groups The internal I/O power supply is interrupted to the left. The bus module is the base for all power supply modules.

The bus module is the base for all X20 24 VDC I/O modules The internal I/O supply is interconnected Manual node number assignment Independent of electronics module Manual and automatic addressing can be combined as desired The BM15 bus module serves as the base for all 24 VDC X20 I/O modules. This bus module is also used to determine a unique address using node number switches.

X20PS3300 Description: Feed for X2X Link and internal I/O supply Electrical isolation of feed and X2X Link supply Redundancy of X2X Link supply possible by operating multiple supply modules simultaneously The supply module is equipped with a feed for the X2X Link as well as the internal I/O supply.

POWERLINK I/O configuration and firmware update via the fieldbus Integrated hub for economical wiring The bus controller makes it possible to connect X2X Link I/O nodes to POWERLINK. It is also possible to operate the X2X Link cycle synchronously 1:1 or synchronous to POWERLINK using a prescaler.

8 digital outputs with 2 A Source connection 1-wire connections Power feed integrated in the module Integrated output protection This module is equipped with 8 outputs for 1-wire connections. The outputs are designed for a source circuit. The nominal output current is 2 A. The output supply is fed directly to the module. An additional supply module is not needed. There is no connection between the module and the I/O supply potential on the bus module.

X20 interface module, 1 RS422/485 interface, max. 115.2 kbit/s

2x / 4x / 6x Fast Ethernet hub Modular construction Easily expandable The X20 hub is a device that can be used universally in standard Ethernet networks or POWERLINK networks. It is suitable for 100 Mbit/s (Fast Ethernet) networks. The bus modules expanded to the left allow connection of up to 2 hub expansion modules in addition to the hub base module. This means that a single base device provides up to 6 hub interfaces.

X2X Link bus receiver Feed for X2X Link and internal I/O supply Electrical isolation of feed and X2X Link supply Redundancy of X2X Link supply possible by operating multiple supply modules simultaneously Operation only on the slot to the far left The bus receiver is used to connect the X20 System to the X2X Link. The module is equipped with a feed for the X2X Link as well as the internal I/O supply.

X20 bus module, 24 VDC coded, internal I/O supply connected through